Apple StyleWriter II Especificações Página 1

Service Source K StyleWriter II

Specifications Environmental - 5 Environmental Acoustic Noise Level Approximately 40 dB (reference level) Temperature 41–95° F (5–35° C) Humidity 10

Specifications Electrical - 6 Electrical Power Source U.S./Canada: 120 VAC, 60 Hz, 0.36 AU.K./Australia: 240 VAC, 50 Hz, 24 WEurope: 220 VAC, 50 Hz,

Specifications Physical - 7 Physical Dimensions Height: 6.8 in. (173 mm)Width: 13.7 in. (347 mm)Depth: 7.6 in. (193.5 mm) Weight Approximately 6 lb.

Service Source K Troubleshooting StyleWriter II

Troubleshooting General/ - 1 General The Symptom Charts included in this chapter will help you diagnose specific symptoms related to your product. B

Troubleshooting Symptom Charts /Preliminary Checks - 2 Symptom Charts Preliminary Checks Computer cannot find printer1 Verify that StyleWriter II dr

Troubleshooting Symptom Charts /Preliminary Checks - 3 Mechanical problems 1 Verify that paper is correct weight.2 Clear paper jam.3 Verify that cut

Troubleshooting Symptom Charts /Status Light - 4 Status Light No status lights 1 Replace fuse.2 Verify that operation cable is securely connected to

Troubleshooting Symptom Charts /Printing - 5 Printing No printing 1 Verify that interface cable between printer and computer is tightly connected.2

Troubleshooting Symptom Charts /Printing - 6 Overprinting 1 Verify that program being used is set for correct line spacing and line length.2 Verify

Service Source K Basics StyleWriter II

Troubleshooting Symptom Charts /Printing - 7 Page prints off center; images are out of place1 Use 16–24 lb. cotton bond paper.2 Verify that sheet fe

Troubleshooting Symptom Charts /Carrier Movement - 8 Carrier Movement Erratic carrier motionReplace printer.Power light is on; carrier does not move

Troubleshooting Symptom Charts/Paper Feed - 9 Paper Feed No paper feed 1 Verify that cut sheet feeder aligns with printer.2 Release paper pressure p

Troubleshooting Symptom Charts /Paper Feed - 10 Paper feed difficulties: binding, tearing1 Verify that forms thickness lever is set correctly (up fo

Troubleshooting Symptom Charts /Miscellaneous - 11 Miscellaneous Operations panel buttons don’t work1 Verify that operations panel cable is securely

Service Source K Take Apart StyleWriter II

Take Apart Covers - 1 Covers No preliminary steps are required before you begin this procedure.Review the ESD precautions in Bulletins/Safety. Cauti

Take Apart Covers - 2 Front Access Cover 1 Note: The front access cover is held in place by two arms that function as hinges. Plastic tabs at the e

Take Apart Covers - 3 Upper Case 1 Release the right side latch and lift the upper case a short distance. Repeat for the left side latch and remove

Take Apart Covers - 4 Output Tray Assembly 1 Pull out the tray until the two tabs rest against the stops. Press down and remove the tray.0utput Tray

Basics Test Page - 1 Test Page Turn on the printer and hold down the online key for at least 6 seconds or until the test page prints.Online Key

Take Apart Covers - 5 Rear Cover 1 Press out the two latches on the bottom of the printer and press up on the rear cover. 2 Release the two latches

Take Apart Covers - 6 Cut Sheet Feeder Cover 1 Press in the front latch and release the side latch. 2 Pull back and remove the cover.Side LatchCut S

Take Apart Covers - 7 Paper Support 1 Pull out the paper support until it rests against the stops. 2 Push the support forward and disconnect the lat

Take Apart Covers - 8 Bottom Cover 1 Using a screwdriver, push out the two front latches. 2 Pull up and remove the bottom cover.FrontBottom CoverFro

Take Apart Covers - 9 Replacement Note: Make sure the bottom cover circular tabs fit into the proper position in the printer frame.

Take Apart Covers - 10 Replacement Note: Make sure the latch on the upper case engages the on/off button on the logic board.LatchOn/Off Button

Take Apart Cut Sheet Feeder - 11 Cut Sheet Feeder Before you begin, remove covers.Review the ESD precautions in Bulletins/Safety. Caution: Do not g

Take Apart Cut Sheet Feeder - 12 1 Using a Phillips screwdriver, remove the two screws that secure the cut sheet feeder to the printer. 2 Press in t

Take Apart Roller and Spring - 13 Roller and Spring Before you begin, remove front cover.Review the ESD precautions in Bulletins/Safety.Front Cover

Take Apart Roller and Spring - 14 1 Push the roller forward slightly. 2 Carefully lift up and remove the roller and spring.

Basics Test Page - 2 The test page shows the ROM revision and a test pattern. Use the test pattern to determine if the ink jets are functioning prop

Take Apart Cut Sheet Feeder Roller - 15 Cut Sheet Feeder Roller Before you begin, remove the following:• Covers• Cut sheet feederReview the ESD prec

Take Apart Cut Sheet Feeder Roller - 16 Caution: When the roller is removed, the feeder gear is loose. Remove the roller slowly so that the gear wi

Take Apart Cut Sheet Feeder Roller - 17 Replacement Note: Align the notch on the upper gear with the upper line on the cut sheet feeder. Align the

Take Apart Carriage Assembly - 18 Carriage Assembly Before you begin, remove the following:• Covers• Cut sheet feederReview the ESD precautions in B

Take Apart Carriage Assembly - 19 1 Disconnect connector CNH from the logic board.Connector CNH

Take Apart Carriage Assembly - 20 2 Remove the plastic ribbon cable and cable holder. Replacement Note: Make sure the ribbon cable holes are mounte

Take Apart Carriage Assembly - 21 3 Press in the two latches. 4 Push up and remove the carriage release clip.LatchCarriage Release ClipLatch

Take Apart Carriage Assembly - 22 5 Carefully remove the shaft clips from each side of the carriage assembly.Shaft Clip

Take Apart Carriage Assembly - 23 6 Move the carriage to the far right and disconnect the carriage from the carriage guide. Caution: Do not remove

Take Apart Carriage Assembly - 24 7 Using a flat-blade screwdriver, carefully press in the idler roller and disconnect the carriage belt.

Service Source K Specifications StyleWriter II

Take Apart Carriage Assembly - 25 8 Hold the carriage assembly and push back the carriage shaft. 9 Slide out the carriage shaft.

Take Apart Carriage Motor - 26 Carriage Motor Before you begin, remove the following:• Covers• Cut sheet feederReview the ESD precautions in Bulleti

Take Apart Carriage Motor - 27 1 Disconnect connectors CNH and CNCR from the main board.Connector CNHConnector CNCR

Take Apart Carriage Motor - 28 2 Using a flat-blade screwdriver, press in the idler roller and disconnect the carriage belt.

Take Apart Carriage Motor - 29 3 Using a Phillips screwdriver, remove the two mounting screws.4 Lift up and pull out the carriage motor.

Take Apart Eject Roller - 30 Eject Roller Before you begin, remove covers.Review the ESD precautions in Bulletins/Safety.Eject Roller

Take Apart Eject Roller - 31 1 Grasp one end of the roller, press it firmly to the side, and snap the roller out of the mounting holes.

Take Apart Fuse - 32 Fuse Before you begin, remove the following:• Covers• Cut sheet feederReview the ESD precautions in Bulletins/Safety.Fuse

Take Apart Fuse - 33 1 Remove the fuse cover and replace the fuse.

Service Source K Exploded View StyleWriter II

Specifications Characteristics - 1 Characteristics Print Methods Serial bubble jet ink-on-demand Throughput SHQ mode 124 cps (10 cpi) HQ mode 173

Exploded View 1Paper Support922-0189Cut Sheet Feeder Roller922-0192Rear Cover922-0184Upper CaseCover922-0185Front Cover922-0186Carriage Belt922-019

Specifications Graphics - 2 Graphics Resolution 360 dpi (at best mode)

Specifications Paper Handling - 3 Paper Handling Paper Size: LTR, LGL, A4Weight: 16–24 lb. Capacity: 100 sheets (A4, LTR) Envelopes Size: Commercial

Specifications Ink Cartridges - 4 Ink Cartridges Type Ink cartridge Ink Color Black Ink Amount Approximately 28 g (per cartridge) Life Approximately