Apple Xserve Intel (Late 2006) DIY Procedure for Power D Manual do Utilizador descarregar pdf

 Xserve (Late 2006)

073-1103 Rev. A

Power Distribution Board

Replacement Instructions

Follow the instructions in this document carefully. Failure to follow these instructions could

damage your equipment and void its warranty.

Online instructions are available at http://www.apple.com/support/diy/.

Working Safely Inside the Xserve

Always touch the Xserve enclosure to discharge static electricity before you touch any

components inside the Xserve. To avoid generating static electricity, do not walk around the

room until you have nished working inside the server and have replaced the cover. To minimize

the possibility of damage due to static discharge, wear an antistatic wrist strap while you work

inside the Xserve.

Warning: Always shut down the Xserve and disconnect the power cords before opening

it to avoid damaging its internal components or the components you are installing. Don’t

open the server while it is turned on. Even after you shut down the Xserve, its internal

components can be very hot. Let it cool before you open it.

Tools Required

The only tool required for this procedure is a Phillips #1 screwdriver. You may also nd a small

atblade screwdriver useful in releasing the connectors on the power distribution board cable.

Removing the Xserve from a Rack

Alert users that the server will be unavailable for a period of time.

Shut down the Xserve (see the Xserve User’s Guide for help) and then wait to let the Xserve

internal components cool.

Warning: Always shut down the Xserve before opening it to avoid damaging its internal

components or the components you want to install or remove. Don’t open the Xserve

or try to install or remove items inside while it is turned on. Even after you shut down

the Xserve, its internal components can be very hot. Let it cool down for 5 to 10 minutes

before you open it.

1 2 3 4 5 6 ... 13 14

Resumo do Conteúdo

Página 1 - Power Distribution Board

 Xserve (Late 2006)073-1103 Rev. APower Distribution BoardReplacement InstructionsFollow the instructions in this document carefully. Failure to foll

Página 2 - Opening the Xserve

Xserve (Late 2006) Power Distribution Board Replacement Instructions 10Installing the Replacement Power Distribution BoardLower the replacement power

Página 3 - Power Supplies

Xserve (Late 2006) Power Distribution Board Replacement Instructions 11Replacing the Drive Interconnect BackplaneLower the backplane into the enclosu

Página 4

Xserve (Late 2006) Power Distribution Board Replacement Instructions 12Tighten the thumbscrew that secures the backplane to the enclosure.Reconnect t

Página 5 - Airow Duct

Xserve (Late 2006) Power Distribution Board Replacement Instructions 13Tighten the ve Phillips screws that fasten the airow duct to the fan array,

Página 6 - Fan Array

Xserve (Late 2006) Power Distribution Board Replacement Instructions 14Closing the XserveReplace and secure the cover.Slide the Xserve back into the

Página 7 - Drive Interconnect Backplane

Xserve (Late 2006) Power Distribution Board Replacement Instructions 2Unplug all cables from the Xserve. Note: If you have trouble releasing a cable

Página 8

Xserve (Late 2006) Power Distribution Board Replacement Instructions 3Removing the Installed Power Distribution BoardNote: Before removing the power

Página 9

Xserve (Late 2006) Power Distribution Board Replacement Instructions 4Power Distribution Board CableLocate the power distribution board cable. Discon

Página 10

Xserve (Late 2006) Power Distribution Board Replacement Instructions 5Caution: The power distribution board cable connectors are tight and can be di

Página 11

Xserve (Late 2006) Power Distribution Board Replacement Instructions 6Fan ArrayLoosen the two thumbscrews that secure the fan array to the enclosure.

Página 12 - Replacing the Airow Duct

Xserve (Late 2006) Power Distribution Board Replacement Instructions 7Drive Interconnect BackplaneRelease the two locking levers on the front panel b

Página 13 - Replacing the Power Supplies

Xserve (Late 2006) Power Distribution Board Replacement Instructions 8Shift the backplane to the left (towards the enclosure side), in the direction

Página 14 - Closing the Xserve

Xserve (Late 2006) Power Distribution Board Replacement Instructions 9Power Distribution BoardLocate the power distribution board. Release the thumbs

Comentários a estes Manuais

Sem comentários

Apple Xserve Intel (Late 2006) DIY Procedure for Power D Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Software Apple Xserve Intel (Late 2006) DIY Procedure for Power D. Apple Xserve Intel (Late 2006) DIY Procedure for Power Distribution Board User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Software Apple Xserve Intel (Late 2006) DIY Procedure for Power D