Apple Xserve Intel (Late 2006) DIY Procedure for Rear ID Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Software Apple Xserve Intel (Late 2006) DIY Procedure for Rear ID. Apple Xserve Intel (Late 2006) DIY Procedure for Rear ID Tab User Manual Manual do Utilizador

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 22
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 0
 Xserve (Late 2006)
073-1112 Rev. A
Rear ID Tab
Replacement Instructions
Follow the instructions in this document carefully. Failure to follow these instructions could
damage your equipment and void its warranty.
Online instructions are available at http://www.apple.com/support/diy/.
Working Safely Inside the Xserve
Always touch the Xserve enclosure to discharge static electricity before you touch any
components inside the Xserve. To avoid generating static electricity, do not walk around the
room until you have nished working inside the server and have replaced the cover. To minimize
the possibility of damage due to static discharge, wear an antistatic wrist strap while you work
inside the Xserve.
Warning: Always shut down the Xserve and disconnect the power cords before opening
it to avoid damaging its internal components or the components you are installing. Don’t
open the server while it is turned on. Even after you shut down the Xserve, its internal
components can be very hot. Let it cool before you open it.
Tools Required
The following tools are required for this procedure:
Phillips #1 screwdriver
Antistatic wrist strap (if available)
2 thermal grease syringes for replacing processor heat sinks (supplied with the replacement
part)
2 alcohol wipes for cleaning processors and heat sinks (supplied with the replacement part)
Vista de página 0
1 2 3 4 5 6 ... 21 22

Resumo do Conteúdo

Página 1 - Rear ID Tab

 Xserve (Late 2006)073-1112 Rev. ARear ID TabReplacement InstructionsFollow the instructions in this document carefully. Failure to follow these inst

Página 2 - Thumbscrews

Xserve (Late 2006) Rear ID Tab Replacement Instructions 10Disconnect the optical drive cable from the logic board.Release the two locking levers on t

Página 3 - Opening the Xserve

Xserve (Late 2006) Rear ID Tab Replacement Instructions 11Release the nine thumbscrews that secure the logic board to the enclosure (highlighted in t

Página 4 - Captive screws

Xserve (Late 2006) Rear ID Tab Replacement Instructions 12Rear ID TabNote: The rear ID tab protrudes from the rear panel through a slot.Locate the re

Página 5 - Airow Duct

Xserve (Late 2006) Rear ID Tab Replacement Instructions 13Gently grasp the ID tab and pull up on it to disengage it from the channel that it slides a

Página 6 - Fan Array

Xserve (Late 2006) Rear ID Tab Replacement Instructions 14Installing the Replacement Rear ID TabInsert the replacement rear ID tab through its slot i

Página 7

Xserve (Late 2006) Rear ID Tab Replacement Instructions 15Clean o any existing thermal grease on the left (CPU B) processor heat sink using the alco

Página 8 - Processor Heat Sinks

Xserve (Late 2006) Rear ID Tab Replacement Instructions 16Clean o any existing thermal grease on the top face of the processor using the alcohol wip

Página 9 - Logic Board

Xserve (Late 2006) Rear ID Tab Replacement Instructions 17Use the edge of the package that the alcohol wipes came in as a spatula to smoothly spread

Página 10

Xserve (Late 2006) Rear ID Tab Replacement Instructions 18Rotate the top of the holder to the closed position.Engage the latch on the metal processor

Página 11

Xserve (Late 2006) Rear ID Tab Replacement Instructions 19Tighten the four captive Phillips mounting screws for the left processor heat sink in the o

Página 12

Xserve (Late 2006) Rear ID Tab Replacement Instructions 2Removing the Xserve from a RackAlert users that the server will be unavailable for a period

Página 13

Xserve (Late 2006) Rear ID Tab Replacement Instructions 20Replacing the Fan ArrayAlign the power connector on the fan array with its connector on the

Página 14 - Replacing the Logic Board

Xserve (Late 2006) Rear ID Tab Replacement Instructions 21Tighten the ve Phillips screws that fasten the airow duct to the fan array, in the order

Página 15

Xserve (Late 2006) Rear ID Tab Replacement Instructions 22Replacing the Power SuppliesSlide the rst power supply all the way into the bay, and then

Página 16

Xserve (Late 2006) Rear ID Tab Replacement Instructions 3Opening the XserveLoosen the thumbscrews at the back of the top cover and slide the cover ba

Página 17

Xserve (Late 2006) Rear ID Tab Replacement Instructions 4PCI Riser Cards and Expansion CardsLoosen the two captive screws that secure the riser brack

Página 18

Xserve (Late 2006) Rear ID Tab Replacement Instructions 5Airow DuctLoosen the ve Phillips screws that fasten the airow duct to the fan array.Pull

Página 19

Xserve (Late 2006) Rear ID Tab Replacement Instructions 6Fan ArrayLoosen the two thumbscrews that secure the fan array to the enclosure. Note: The th

Página 20 - Replacing the Airow Duct

Xserve (Late 2006) Rear ID Tab Replacement Instructions 7Note: You may encounter some resistance around the fan array power connector during removal.

Página 21

Xserve (Late 2006) Rear ID Tab Replacement Instructions 8Disconnect the backplane-to-logic board cable from the drive interconnect backplane and remo

Página 22 - Closing the Xserve

Xserve (Late 2006) Rear ID Tab Replacement Instructions 9Important: Each heat sink is connected to the logic board by a small 2-pin thermal sensor ca

Comentários a estes Manuais

Sem comentários